- 您现在的位置：买卖IC网 > Sheet目录409 > DNT24DK (RFM)RF EVAL FOR DNT24P
DNT24 I/O Descriptions
Pin
1
Name
GND
I/O
-
Description
Power supply and signal ground. Connect to the host circuit board ground.
This pin’s default configuration is data activity output. On a base, this signal blinks when a valid packet is
2
ACT
(DIAG_TX)
O
(O)
received. On a remote, this signal blinks when a packet is transmitted. On a router, this signal blinks when
a valid upstream packet is received or a downstream packet is transmitted. Alternate pin function is the di-
agnostic serial port output.
This pin’s default configuration is data carrier detect output. On a base, this signal is asserted when any
3
/DCD
(DIAG_RX)
O
(I)
valid packet is received, and is cleared if no packets are heard for the configured router/remote registra-
tion time-out interval. On a router or remote, this signal is asserted when the radio obtains hopping pattern
synchronization, and remains asserted until no beacons are heard for 50 hops. Alternate pin function is
the diagnostic serial port input.
Configurable digital I/O port 0. When configured as an input, an internal pull-up resistor can be selected
4
GPIO0
I/O
and direct interrupt from sleep can be invoked. When configured as an output, the power-on state is
configurable. In sleep mode the pin direction, input pull-up selection or output state are also separately
configurable.
5
6
7
8
9
10
11
12
13
14
15
16
17
RADIO_TXD
RADIO_RXD
GPOI4
(/HOST_CTS)
GPOI5
( /HOST_RTS)
DAC0
GPIO2
GPIO1
GPIO3
(DAV)
DAC1
VCC
GND
GND
/RESET
O
I
I/O
(O)
I/O
(I)
O
I/O
I/O
I/O
(O)
O
I
-
-
I
Serial data output from the radio.
Serial data input to the radio.
Default pin function is GPIO4 with the same configuration options as GPIO0. Alternate pin function is
UART/SPI flow control output. The module sets this line low when it is ready to accept data from the host
on the RADIO_RXD or MOSI input. When the line goes high, the host must stop sending data.
Default pin function is GPIO5 with the same configuration options as GPIO0. Alternate pin function is
UART/SPI flow control input. The host sets this line low to allow data to flow from the module on
the RADIO_TXD pin. When the host sets this line high, the module will stop sending data to the host.
12-bit DAC 0 output. Full scale output can be referenced to the voltage at pin 25 or the 3.3 V regulated
module bus voltage.
Configurable digital I/O port 2. Same configuration options as GPIO0.
Configurable digital I/O port 1. Same configuration options as GPIO0.
Default pin function is GPIO3 with the same configur ation options as GPIO0. When SPI slave mode oper-
ation is enabled, a logic high on this pin indicates when data is available to be clocked out by the SPI
master.
12-bit DAC 1 output. Same specifications and configuration options as DAC0.
Power supply input, +3.3 to +5.5 Vdc.
Power supply and signal ground. Connect to the host circuit board ground.
Power supply and signal ground. Connect to the host circuit board ground.
Active low module hardware reset.
ADC input 0. This pin is a direct ADC input when the ADC is operating in single-ended mode, or the differ-
ential negative input for positive inputs applied to ADC1 or ADC2 when the ADC is operating in differential
mode. Full-scale reading can be referenced to Pin 25 for ratiometric measurements. For absolute mea-
18
ADC0
I
surements, the ADC can use either the regulated supply voltage divided by 1.6 (about 2.06 V), or an ex-
ternal voltage applied to Pin 25. In single-ended mode, ADC measurements are 11-bit unsigned values
with full scale nominally 2.7 V when referenced to a 2.7 V input on Pin 27. In differential mode, ADC mea-
surements are 12-bit signed values.
19
20
21
22
ADC1
MISO
MOSI
/SS
I
I/O
I/O
I/O
ADC input 1. Direct input when the ADC is operating in single-ended mode, positive differential input rela-
tive to ADC0 when the ADC is operating in differential mode.
This pin is the SPI master mode input or slave mode output.
This pin is the SPI master mode output or slave mode input.
SPI active low slave select. This pin is an output when the module is operating as a master, and an input
when it is operating as a slave.
www.RFM.com E-mail: info@rfm.com
? 2011-2012 by RF Monolithics, Inc.
Page 4 of 7
DNT24 - 08/01/12
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DNT900DK
DEVELOPMENT KIT FOR DNT900 MOD
DNW1-DW10/12.5MM/BLA
LAMP T-1.25 NEO WEDGE 14V 100MA
DNW1-DW48/GRA
LAMP T-1.25 NEO WEDGE 14V
DNW1-EW87/GRA
LAMP T-1.25 NEO WEDGE 14V
DP1203C4333LF
MODULE DROPIN FOR XE1203F 433MHZ
DP1203C4333
MODULE DROP IN FOR XE1203 433MHZ
DP1205C433LF
MODULE DROP IN FOR XE1205 433MHZ
DP1283C915
MODULE DROP IN FOR XE1283 915MHZ
相关代理商/技术参数
DNT24MC
功能描述:射频模块 2.4GHz FHSS Radio SMD U.FL
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT24MCA
功能描述:射频模块 2.4GHz FHSS Radio SMD Chip Ant.
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT24MP
功能描述:射频模块 2.4GHz FHSS Radio Pinned U.FL
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT24MPA
功能描述:射频模块 2.4GHz FHSS Radio Pinned Chip Ant.
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT24P
功能描述:射频模块 2.4 GHz 10 and 63mW 128 Bit AES
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT24PA
功能描述:射频模块 2.4 GHz 10 and 63mW 128 Bit AES
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
DNT25SX
制造商:CEEP 功能描述:SOCKET D T&D 25WAY
DNT37SX
制造商:CEEP 功能描述:SOCKET D T&D 37 WAY